Same lean, tighter line: the car park circle drill
Hold one lean angle on a steady circle in an empty car park. Roll off and it tightens, a little front brake tightens it further, and a gentle throttle opens it.
3 min readBy PitPin Desk
Dave of Canyon Chasers treats lean angle as evidence of how much grip you are spending on cornering. Yamaha Champions Riding School calls the budget 100 points of grip, spent on braking, accelerating and cornering. You cannot spend a hundred and one. What cornering does not use is left in reserve for the gravel you did not see, the deer, the corner that tightens and the car in your lane.
Speed sets the radius
At a given lean angle, speed equals radius. Go faster and the arc gets bigger. Slow down and the arc gets smaller all by itself, with no extra lean required.
Practise it in an empty car park. Get the bike into a big steady circle and try to hold the lean angle exactly the same. Roll off the throttle and the circle tightens. Do it again, gently adding light front brake pressure, and it tightens a lot. Then a third time, accelerating gently, and the circle opens up. One lean angle has produced three radii, and you have not steered the circle wider or tighter with the bars.
Why the front brake tightens the line
The front brake makes the bike slow down and turn. Weight goes onto the front tyre, the forks compress, rake and trail come down, the wheelbase shortens, and the bike wants to change direction.
Throttle does the opposite. The bike speeds up, so it wants to run wide. Accelerating shifts weight rearward and extends the forks, which increases rake and trail, and the bike does not want to turn. It is harder to steer at the moment you are asking it to steer more. Less weight on the front tyre also means less front grip.
Dave calls countersteering one very effective way to start the lean, and says that is the whole job. The motorcycle turns because it is leant over and the front wheel is allowed to turn. How tightly it turns depends largely on how fast it is going. Geometry, the brake and speed decide what that lean does. The advice that says, if you are running wide, just countersteer and lean more, assumes you stay on the throttle. He calls it perfectly good advice on a freeway on-ramp or in a large empty car park, and says it leaves fewer choices in a blind corner or on variable asphalt.
Where early throttle leaves you
To spend longer on the side of the tyre, a rider leans the bike early, gets back to the throttle early to keep it there, and adds lean to counteract the forces pushing the bike wide. When the corner tightens more than he expected, he adds lean again. The bike is then further over, on a smaller contact patch, actively fighting him, going faster than he intended, with almost no braking left. Dave calls this one of the primary causes of single-vehicle motorcycle crashes.
Apart from a few specific situations, don't add lean and throttle at the same time. Don't add lean and brake pressure at the same time either. As lean goes up, brake pressure comes down. As the throttle comes on, lean comes off. Once the jargon is gone, he says, trail braking is that trade: front brake pressure eases off as the lean increases.
Where maximum lean belongs
Every bend has a place where the bike has to change direction, and that is where you need the most lean, so be at your slowest there. Finish the braking, get the bike pointed, and only once you are aimed out of the corner, start trading lean for throttle. Stay wide on the way in, and wait until you can see the exit. When the apex turns up and the corner opens out in front of you, make that trade. By the time the throttle is properly open, he says, the bike is nearly upright and the radius of the line has gone to infinity.
One corner you know
The homework does not need a car park, cones or any extra speed. It needs one corner you know well. Ride it once as you normally would, then again at the same speed and on the same line, from the feet up. Ball of the inside foot on the peg, not the arch and not the heel. Flex the calf in a calf raise on the peg, and drive your weight down into it. Rest the outside leg against the tank. His cue is a flashlight in your belly button, pointed through the corner, so your chest, shoulders, head and eyes follow it.
Three things happen at once, and he wants all three. Your weight sits low, which drops the combined centre of mass. You prop yourself up, so your chest and head can move inside without your arms hauling you there. Weight comes off your hands. The last of those is the big one for him: a lot of riders who feel the bike does not want to turn are gripping the bars so hard that they are personally preventing it from turning.
For a given corner at a given speed, the total lean of rider and bike together is fixed. Counterlean, sitting upright while the bike goes over underneath you, means the bike has to do all of that lean. Move the combined centre of mass to the inside and the bike sits up. From the same 20 degrees of total lean, he has the bike at 15 degrees instead of 26. If the corner, your speed or your mood does not require all of that, he says you get about 80% of the way there by pointing that flashlight, flexing the ankle and putting your weight on your inside sit bone. On the second pass, same corner and same speed, the bike leans less.