PitPinTrack day riders’ news & tips, pinned daily

Knee down takes more than body position, says Life at Lean

The rider behind Life at Lean was on track for 18 months before his first knee down. The fixes are body position, trust in the bike and the tyres, trust in your own skill, and the brake release.

3 min readBy PitPin Desk

The rider behind Life at Lean had been on track for 18 months and was going pretty well in the advanced group. His first knee down came at Snetterton in 2011, during a coaching session with Neil Hodgson. He says you could argue that knee down is pretty arbitrary and doesn't really make you a better rider. The video goes through the reasons riders struggle with it, which go beyond body position.

Get the knee out past the peg

The peg is typically the first part of the bike to touch down as the bike reaches maximum lean. If your knee sticks out further than the peg, relative to the contact patch, the knee should always touch the ground first. Short legs make that harder, because they do not stick out as far. Knee down is still possible if the next pieces are right, which gives you the best chance.

The video's checklist is to slide off the seat, with half to one whole cheek usually enough, turn your heel in so your toes point out, and face your body slightly into the turn. A crossed-up position, pointing away from the corner, forces the knee forward towards the front of the bike instead of out to the side. Fixing these helps open the hips and extend the knee further out.

You also need to be relaxed enough to actually open your hips. With poor lower body support you rely on your arms, which typically lets your head drift back into the centre, creating that same crossed-up position. You may also find a little too much strain in your legs, which makes it hard to relax and open your hips. There is always a good deal of weight on the inside peg, because most of your mass is on top of it. Good body position and anchoring keep that from becoming excessive, so the knee is easier to stick out.

Trust the bike and yourself

With the knee far enough out, the bike still has to lean far enough. Life at Lean typically sees two things behind the fear of leaning. The rider does not trust the bike and tyres, or does not trust their own ability not to crash.

For the bike and tyres, watch riders on similar machinery and tyres going much faster, the bike cranked right over and the knee on the deck. That in itself, he says, is proof the equipment can do it. Stickier rubber can help if your tyres are not giving you confidence. That doesn't mean buying the stickiest race rubber you can: his example is a move from a sports touring tyre to a modern track day tyre, for the extra feeling of grip that could make all the difference.

For yourself, learn the fundamental skill, and what you should be doing with the controls at any given moment, so you know you are doing things correctly.

Roll speed in with the brake release

Braking later and attacking the corner strips the speed you need through over-braking, and it takes away the calmness and composure you need as well. Rolling off a long way before the corner, while barely using the brakes, makes it hard to carry more speed in. In his experience, the best approach is something in the middle, on a slightly longer medium-speed corner that needs a fair bit of braking but not high levels of it.

Palmer at Snetterton is his example. It is a medium-speed corner where you spend a fair bit of time, so there is more time to watch your lean angle and your knee. The corner before is a slow hairpin, so you do not need hard brakes. That makes it easier to stay calm and be deliberate with the braking, which is how you roll more speed into the corner.

Release the brake lever a little earlier and quicker at the end of the braking, with everything else the same, and you roll more speed in. If you did roll more speed in, you will likely feel a mild sense of panic that you are going too fast. He says that is completely normal. Keep your eyes up and ahead, so you can see the space is there.

When you meet your lean angle barrier again, push gently on the inside bar, off the throttle or at most neutral throttle, and the bike will lean more. Stick the knee out. Ordinarily you don't want to strain to do that, but it is fine if that is what gets the first touch.

If it does not touch, release the brake lever a little earlier again so you go a little faster next time. If you feel you are barely braking and still not going fast enough, you probably need to move the initial braking point closer to the corner so you are actually using the brakes, and you get that adjustability back.

Life at Lean says this isn't necessarily the perfect approach for going fast. It isolates the barrier and makes it as easy as possible to tackle. Once you can do it consistently on one corner, that confidence starts to carry into the others, and you start getting a knee down there as well.

Sources